My Tutorial

Toni's Little Town

Building 2

*****************

First Open the Imagines for Building 2

You will have a half of a Door, Window

And a Roof

************

1.) You will Now start on the Building 1 Layer

And Add a New Raster Layer=Load from Disk

*1-Building2 Bottom Wall* Flood fill with this

Color #C29372 Now keep this selected

Go to Effects/Textures/Fine Leather/

Use these Settings

Now deselect and Go to Effects to Photo

Enhance and go to Clarity setting at 5

And Repeat this again Now rename this

Layer *Arch*

************

2.) Add a New Raster Layer and go to Layers

And Arrange down and then Load from Disk

*2-Building2 Arch Shadow*

Change your foreground  Color

Flood fill it with this color #40000 deselect

Rename * Arch Shadow*

************

3.) Now go back to your* Arch Layer*

We will stay here for a Bit

Load from Disk=*3-Building2 Center Outer

Bevel* change your foreground color

Back to #C29372  Flood Fill with this color

Keep selected go to Effects Outer Bevel

Don't worry about the picture just the settings

Use these Settings

4.) Deselect But we will stay on this layer

Load from Disk=*4-Building2 Wall Outer Bevel Left*

Flood fill with the same color #C29372

Same setting we Just did Now the Picture will Match

he he he

*********

5.) Now deselect stay here again Load from Disk=

* 5-Building2 Wall Outer Bevel Right*

Flood Fill with same color #C29372 use the

Same Outer Bevel setting again deselect

Boy!!! sure a lot of work for some Bumps on a Wall

he he he

*********

6.) We are going to Stay here don't move =0)

Load from Disk=

*6.) Top Trim on Building Arch* Flood fill

With the same color #C29372 keep selected

And use the Same Outer Bevel

Setting as before see screen shot and deselect

***********

7.) Now Click on your *Arch Shadow* layer

And Arrange it down Under your Arch Layer

Now Add  from your *Arch Shadow Layer*

A New Raster Layer

 And Now Open your *Door image*

Now Load from Disk= *7-Building Door on Left*

Keep selected and Copy and Paste your Door

* Into SELECTIONS*

Now deselected it and rename this layer

* Door Left*

***********

8.) Stay on the Door layer and Add a New Raster Layer

And Arrange down=Load from Disk

*8- Building2 Door on Right*

Now go to your Door image and Mirror it

And Copy and Paste *Into SELECTIONS*

Deselected it and Rename *Door Right*

************

9.) Go to Your *Building1 layer* From there

Add New Raster Layer

Load from Disk*9-Top PART of Building2 wall*

Flood fill with color #C29372

Keep selected go to Effects/Textures/Textures Brick

Use these Settings

You Can go to Color/Adjust/Brightness/Contrast

And Darken if you would Like I did but that's

Up to you deselected  Rename this Layer

* Top Bricks*

10.) Stay on this Layer Load from Disk=

*Window2 Cut-Out*

Now Hit your Delete Key and deselected

Now get your Little window for this Building

And Copy and Paste over the Cut-Out

And Arrange it deselected

************

11.) Stay on *Top Brick Layer* Now Load from

Disk=*Top Trim On Building 2*

Flood fill with color # C29372 keep selected

Go to Effects Inner Bevel using these settings

Now deselect  Rename this layer * Top Trim*

************

12.) Add a New Raster Layer=Load from Disk=

* 12-Small Top Trim* Flood fill and do the

Same Inner Bevel as we just did deselect

Rename *Small Top Trim*

************

13.) All Most done ..Remember I said All Most

he he he

Go Down to your *Top Brick layer*

Add a New Raster Layer and Arrange Down

Load from Disk=*13-Long thin Strip on Right*

Flood fill with color #C29372 keep selected Go

Effects Inner Bevel using theses settings

Now Go to Color =Adjust/Brightness/Contrast/

Use these Settings

You can Make Adjustments to these Numbers

If you wish too

Deselect and Rename *Long Post*

*********

Ok Big Finish lets here the Music Now

he he he

14.) Stay on the Long Post layer Add

A New Raster Layer

Load from Disk=*14-Building2 Roof* and keep selected

Copy and Paste your *Roof Image* Into SELECTIONS

Deselect and Rename * Roof*

I sure Hope you have Two Buildings Now

Or I am in Big Trouble

he he he

***********

15.) Ok Now Close out your Door Window and Roof

We sure don't need them anymore

Now Close out Your Building1 with the X

And go to your *Long Post Layer* go to Layers

And Merge=Merge Visible Rename this Layer

*Building2*

Now On your Layer Palette you should have I Hope

he he he

*Building 1 and Building2*

***********

Ok On We Go to Building3

GraphicsByToni

©copyrights2004